Condition Based parameters
Now, let’s see condition based parameters. These parameters depends upon some specific condition, which is also given below. If that condition is satisfied, then these parameters has to be on nameplate of the circuit breaker.
শর্ত ভিত্তিক প্যারামিটার সমূহ:
এখন, কন্ডিশন ভিত্তিক প্যারামিটার দেখি। এই প্যারামিটার কিছু নির্দিষ্ট অবস্থার উপর নির্ভর করে, যা নীচে দেওয়া হয়েছে। যদি সেই শর্তটি সন্তুষ্ট হয়, তাহলে এই পরামিতিগুলি সার্কিট ব্রেকারের নেমপ্লেটে থাকতে হবে।
Rated switching impulse withstand voltage
Condition : Applicable only for circuit breakers including & above 300kV
Switching surges are generally occurs above 245kV voltage level. And hence you’ll only find this parameter on the circuit breaker above 245kV level.
It becomes important to test the breaker above 245kV voltage level for switching surges. Switching surges are generally caused by energisation of lines or switching of transformers, etc. For 420kV voltage level, switching voltage is specified as 1050kV peak.
Unit : kV Peak
রেটেড সুইচিং ইমপালস ভোল্টেজ সহ্য করে
শর্ত: শুধুমাত্র 300kV সহ সার্কিট ব্রেকারগুলির জন্য প্রযোজ্য
স্যুইচিং সার্জ সাধারণত 245kV ভোল্টেজ স্তরের উপরে ঘটে। এবং তাই আপনি শুধুমাত্র 245kV স্তরের উপরে সার্কিট ব্রেকারে এই প্যারামিটারটি খুঁজে পাবেন।
স্যুইচিং সার্জেসের জন্য 245kV ভোল্টেজ স্তরের উপরে ব্রেকার পরীক্ষা করা গুরুত্বপূর্ণ হয়ে ওঠে। স্যুইচিং সার্জগুলি সাধারণত লাইনের শক্তি বা ট্রান্সফরমারের সুইচিং ইত্যাদির কারণে ঘটে। 420kV ভোল্টেজ স্তরের জন্য, সুইচিং ভোল্টেজকে 1050kV পিক হিসাবে নির্দিষ্ট করা হয়।
ইউনিট: কেভি পিক
DC component of short circuit current
Condition : It has to be on nameplate if it is more than 20%
DC component is a DC component of short circuit current. And if it is more than 20% at the time of contact separation of CB, then it has to be on name plate.
Unit : %
শর্ট সার্কিট কারেন্টের ডিসি উপাদান
শর্ত: এটি নেমপ্লেটে থাকতে হবে যদি এটি 20% এর বেশি হয়
DC কম্পোনেন্ট হল শর্ট সার্কিট কারেন্টের একটি DC কম্পোনেন্ট। এবং যদি এটি CB-এর যোগাযোগ বিচ্ছেদের সময় 20%-এর বেশি হয়, তবে এটি নাম প্লেটে থাকতে হবে।
ইউনিট: %
Rated line charging current
Condition : Applicable only for circuit breakers including & above 72.5kV
This is the highest amount of line charging current a circuit breaker is capable of breaking. This type of current is generated because of the switching of loaded or unloaded overhead lines. So, for 420kV CB IEC has defined the rating equal to 600A.
Unit : Ampere
রেট লাইন চার্জিং বর্তমান
শর্ত: 72.5kV এর উপরে এবং সহ সার্কিট ব্রেকারগুলির জন্য শুধুমাত্র প্রযোজ্য
এটি একটি সার্কিট ব্রেকার ভাঙতে সক্ষম লাইন চার্জিং কারেন্টের সর্বোচ্চ পরিমাণ। লোড করা বা আনলোড করা ওভারহেড লাইনের স্যুইচিংয়ের কারণে এই ধরনের কারেন্ট তৈরি হয়। সুতরাং, 420kV CB-এর জন্য IEC 600A এর সমান রেটিং নির্ধারণ করেছে।
ইউনিট: অ্যাম্পিয়ার
Classification
Condition : If class in not E1 & M1
If circuit breakers mechanical endurance class and electrical endurance class is different from M1 and E1, then it has to be on nameplate. Let me tell you what is mechanical endurance class and electrical endurance class.
Mechanical Endurance Class
- M1 Class
If the breaker is of M1 class which is also called as normal mechanical endurance class, then the breaker has to withstand 2000 no load operations. - M2 Class
If the breaker is of M2 class which is also called as Extended mechanical endurance class, then the breaker has to withstand 10,000 no load operation.
Electrical Endurance Class
E1 stands for Electrical endurance. Generally most of the breaker nowadays are of E1 class. E2 class is an extended electrical endurance class which indicate that, the interrupting parts of the breaker does not require maintenance during its expected operating life.
Please note, as per IEC 62271-100 E2 class is limited to distribution circuit breaker upto 52kV.
শ্রেণীবিভাগ
শর্ত: যদি ক্লাস E1 এবং M1 না হয়
যদি সার্কিট ব্রেকার যান্ত্রিক সহনশীলতা শ্রেণী এবং বৈদ্যুতিক সহনশীলতা শ্রেণী M1 এবং E1 থেকে ভিন্ন হয়, তাহলে এটি নেমপ্লেটে থাকতে হবে। আমি আপনাকে বলি যান্ত্রিক সহনশীলতা শ্রেণী এবং বৈদ্যুতিক সহনশীলতা শ্রেণী কি?
মেকানিক্যাল এন্ডুরেন্স ক্লাস
এম 1 ক্লাস
যদি ব্রেকারটি M1 ক্লাসের হয় যাকে সাধারণ যান্ত্রিক সহনশীলতা শ্রেণীও বলা হয়, তাহলে ব্রেকারকে 2000 নো লোড অপারেশন সহ্য করতে হবে।
M2 ক্লাস
যদি ব্রেকারটি M2 ক্লাসের হয় যাকে এক্সটেন্ডেড মেকানিক্যাল এডুরেন্স ক্লাসও বলা হয়, তাহলে ব্রেকারকে 10,000 নো লোড অপারেশন সহ্য করতে হবে।
বৈদ্যুতিক সহনশীলতা ক্লাস
E1 মানে বৈদ্যুতিক সহনশীলতা। সাধারনত আজকাল বেশিরভাগ ব্রেকার ই 1 ক্লাসের। E2 ক্লাস হল একটি বর্ধিত বৈদ্যুতিক সহনশীলতা শ্রেণী যা নির্দেশ করে যে, ব্রেকারের বিঘ্নিত অংশগুলির প্রত্যাশিত অপারেটিং লাইফের সময় রক্ষণাবেক্ষণের প্রয়োজন হয় না।
অনুগ্রহ করে মনে রাখবেন, IEC 62271-100 অনুযায়ী E2 ক্লাস 52kV পর্যন্ত ডিস্ট্রিবিউশন সার্কিট ব্রেকারে সীমাবদ্ধ।
C1 & C2 class of circuit breaker
On the nameplate, if you see, it is mentioned as M2 & C2. M2 class we just saw. But what is C2 class? Let’s see that. Breaker with class C1 indicates, “Low probability of restrike during breaking of capacitive currents”. Whereas, C2 class breaker indicates, “very low probability of restrike during breaking of capacitive currents”.
So, this was about the condition based parameters. Now let’s look at the optional parameters.
সার্কিট ব্রেকারের C1 এবং C2 ক্লাস
নেমপ্লেটে, আপনি যদি দেখেন, এটি M2 এবং C2 হিসাবে উল্লেখ করা হয়েছে। M2 ক্লাস আমরা এইমাত্র দেখেছি। কিন্তু C2 ক্লাস কি? সেটা দেখা যাক। ক্লাস C1 সহ ব্রেকার নির্দেশ করে, "ক্যাপাসিটিভ স্রোত ভাঙার সময় স্ট্রাইকের কম সম্ভাবনা"। যেখানে, C2 ক্লাস ব্রেকার নির্দেশ করে, "ক্যাপাসিটিভ স্রোত ভাঙার সময় স্ট্রাইকের খুব কম সম্ভাবনা"।
সুতরাং, এই শর্ত ভিত্তিক পরামিতি সম্পর্কে ছিল. এখন ঐচ্ছিক পরামিতিগুলি দেখুন।
Optional Parameters
These parameters are completely optional as per the IEC standard. And hence, it can be or cannot be on the nameplate, depends upon the manufacturer.
Rated out of phase current
If the breaker is used for synchronising two different system, it may happen that the breaker has to open when the systems are in synchronism procedure. And the current generated during this condition is called as out of phase current.
This current gives the highest amount of transient recovery voltage across the breaker contacts and hence it is one of the critical duty to break. Generally, out of phase breaking current is 25% of rated short circuit breaking current. On the nameplate you can see the out of phase current is 12.5kA which is 25% of rated short circuit breaking current I.e. 50kA.
Unit : kV
যদি ব্রেকারটি দুটি ভিন্ন সিস্টেম সিঙ্ক্রোনাইজ করার জন্য ব্যবহার করা হয়, তাহলে এমন হতে পারে যে সিস্টেমগুলি সিঙ্ক্রোনিজম পদ্ধতিতে থাকা অবস্থায় ব্রেকারটি খুলতে হবে। আর এই অবস্থায় উৎপন্ন কারেন্টকে বলা হয় আউট অফ ফেজ কারেন্ট।
এই কারেন্ট ব্রেকার কন্টাক্ট জুড়ে সর্বোচ্চ পরিমাণ ক্ষণস্থায়ী পুনরুদ্ধার ভোল্টেজ দেয় এবং তাই এটি ভাঙ্গার অন্যতম গুরুত্বপূর্ণ দায়িত্ব। সাধারণত, ফেজ ব্রেকিং কারেন্টের 25% রেটেড শর্ট সার্কিট ব্রেকিং কারেন্ট। নেমপ্লেটে আপনি দেখতে পাচ্ছেন যে আউট অফ ফেজ কারেন্ট হল 12.5kA যা রেট করা শর্ট সার্কিট ব্রেকিং কারেন্টের 25%। 50kA
ইউনিট: কেভি
Rated cable Charging
This is the highest amount of cable charging current a breaker is able to break. Cable charging current can occur while switching the unloaded cables.
Don’t get confused between line charging and cable charging both are different. Line charging refers to overhead lines whereas, cable charging refers to underground cables.
Unit : Ampere
Rated single capacitor bank breaking current
This is the highest amount of a single capacitor bank current a breaker is capable of breaking. Switching of capacitive and inductive current is a bit difficult task for the breaker. Because, voltage and current in capacitive and inductive circuit is not in phase with each other.
Unit : Ampere
Rated back to back capacitor bank breaking current
Back to back capacitor bank switching is a special application, and not all the breakers are intended for this. While switching back to back capacitor banks, inrush current is very high and hence there is a high possibility that the arc will restirke. So, if the breaker is made for back to back capacitor bank switching, then you’ll find this parameter on the nameplate of SF6 circuit breaker.
Unit : Ampere
So, these are the optional parameters you can find on the name plate of HV or EHV circuit breaker.
So, that is all for this post. I hope you have learned about all the different parameters about the circuit breaker. If you found this post helpful then do share this post with the people you think might be interested to learn about all these parameters. Also, highly recommend to have a look at our course on circuit breaker control schematics in which you’ll learn all about the secondary wiring & logic of the circuit breaker.
উইকিপিডিয়া ও ইন্টারনেট হতে তথ্য, ছবি সংগৃহীত
No comments:
Post a Comment